Adic 4000 Bedienungsanleitung Seite 1

The 4000/7000DLTTabletop SeriesInstallation and Operation Guide

x Tables 62-0162-01

1IntroductionOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-

1-2 Introduction 62-0162-01

Overview 1-3 1-OverviewThis manual contains information and instructions necessary for the safe operation of the 4000/7000DLT Series. The topics disc

1-4 Introduction 62-0162-01Chapter 6Troubleshooting and Diagnostic - Describes the troubleshooting and diagnostic techniques for the 4000/7000DLT Ser

2DescriptionOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-

2-2 Description 62-0162-01

Overview 2-3 2-OverviewThis section of the document provides a physical description of the switches, indicators and connectors on the front and rear

2-4 Description 62-0162-01The removable tape media cartridge allows long-term off-line and/or off-site data storage. The tape media is rated at up to

Description 2-5 Figure 2-1 7000DLT Front Panel

ii© Copyright 1999 all rights reserved.Quantum® is a registered trademark and DLT™ is a trademark of Quantum Corporation. All other trademarks are pro

2-6 Description 62-0162-01Figure 2-2 4000DLT Front Panel

Description 2-7 Table 2-4 Front Panel Indicators and Controls2-line by 20-character LCD DisplayDisplays drive status, error messages, POST resultsBee

2-8 Description 62-0162-01Rear Panel Controls and ConnectorsFigure 2-3 on page 2-8 shows the controls and connectors located on the rear panel of the

Description 2-9 Data CartridgeThe data cartridges used in the DTL7000 Series are housed in 4-inch plastic cases and employ 1/2-inch metal particle ta

2-10 Description 62-0162-01Figure 2-4 DLT Data CartridgeAlways remove any cartridge from the drive before turning off host system power. Failure to r

Other Requirements 2-11 SCSI Interface CableThe kind of cable you need will depend on the kind of SCSI bus connector on your host adapter. The 7000DL

2-12 Description 62-0162-01

3SafetySafety Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-3Precaution

3-2 Safety 62-0162-01

Safety Conventions 3-3 3-Safety ConventionsThe following symbols are used throughout the document.The danger exists of a fatal electric shock. At pla

Contentsiii1IntroductionOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3-4 Safety 62-0162-01All safety and operating instructions should be read before this product is operated, and should be retained for future referenc

Precautions 3-5 Use the unit on a firm level surface free from vibration, and do not place anything on top of unit.

3-6 Safety 62-0162-01

4InstallationOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

4-2 Installation 62-0162-01

Overview 4-3 4-OverviewThis chapter explains the steps necessary to install and test your 4000/7000DLT Series. It also provides an information symbol

4-4 Installation 62-0162-01Connecting More than One 4000/7000DLT SeriesIf you are connecting more than one 4000/7000DLT Series unit on the same SCSI

Setting the SCSI ID 4-5 Setting the SCSI IDDepending upon your setup, operating system and number of SCSI devices on the bus, you may have to change t

4-6 Installation 62-0162-01Count each device's SCSI ID in sequence 0 to 7 (or 0 to 15), on each SCSI bus to confirm that no two devices have the

Connecting Power and Turning On 4-7 Connecting Power and Turning On Step 1 Plug the power cord into the back of the 4000/7000DLT Series.Step 2 Plug th

iv Contents 62-0162-01 Additional Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-123

4-8 Installation 62-0162-01

5Operation and MaintenanceOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2 Operation and Maintenance 62-0162-01

Overview 5-3 5-OverviewThis section describes normal operating features of the 4000/7000DLT Series. Additionally, it explains how, and when, to clean

5-4 Operation and Maintenance 62-0162-01Drive StatusLED IndicatorsAfter initialization, the drive will be in one of the four states listed in Table 5-

Drive Status 5-5 LCD MessagesTable 5-2 describes the messages displayed on the LCD during and immediately after the POST.Table 5-2 Drive Status LCD Me

5-6 Operation and Maintenance 62-0162-01POST completes in about 13 seconds and the drive responds normally to all ommands. However, it may take longer

Drive Operating Conditions 5-7 Left Indicator Panel LEDLabel Color State Operating Condition2.6 Yellow ONBlinkingTape is recorded in 2.6 format.Tape i

5-8 Operation and Maintenance 62-0162-01LCD MessagesTable 5-4 on page 5-8 describes the messages displayed by the LCD during normal operation:Table 5-

Drive Operating Conditions 5-9 When tape is loaded.DLTtype = DLTTM4000 (4000DLT), or DLTTM7000 (7000DLT).Compressed if compression mode enabled or Sta

Contents v LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-4LCD Messag

5-10 Operation and Maintenance 62-0162-01Whenever the system is writing to a tape, these two messages will alternate. Each message will be displayed f

Drive Operating Conditions 5-11 The drive head needs cleaning or the tape is bad.followed by:If new tape, or the drive cannot initialize the tape. fol

5-12 Operation and Maintenance 62-0162-01Loading the Data CartridgeDue to static the label or other items included in this package will occasionally c

Data Protection 5-13 Step 3 Insert the data cartridge into the slot.Step 4 Push the cartridge into the drive. Step 5 Push the Cartridge Insert/Release

5-14 Operation and Maintenance 62-0162-01Table 5-5 indicates what is happening during cartridge use:Removing the Data CartridgeRemove a cartridge from

Cleaning the Tape Head 5-15 Step 4 Push the Cartridge Insert/Release Handle closed.When you remove the cartridge from the drive, return the cartridge

5-16 Operation and Maintenance 62-0162-01Using cloth swabs, cotton swabs, cleaning agents, or unapproved cleaning cartridges will void your warranty.

Cleaning the Tape Head 5-17 To clean the head, use a cleaning cartridge. Inert the cleaning cartridge in the drive as described in Loading the Data Ca

5-18 Operation and Maintenance 62-0162-01Do not remove the cleaning cartridge before the drive sounds the beeper.Remove the cleaning cartridge from th

6Troubleshooting and DiagnosticOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

vi Contents 62-0162-01 BDrive ConfigurationDrive Dependent Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6-2 Troubleshooting and Diagnostic 62-0162-01

Overview 6-3 6-OverviewThis section lists a number of common problems and the actions to take to correct them. It provides information on why the DLT

6-4 Troubleshooting and Diagnostic 62-0162-01Your system does not recognize the 4000/7000DLT Series unit (Continued)The SCSI bus may not be correctly

Use Cleaning Tape LED 6-5 Use Cleaning Tape LEDIf an excessive number of read-after-write errors are detected during normal operation of the 4000/700

6-6 Troubleshooting and Diagnostic 62-0162-01Why the Use Cleaning Tape LED Gets Turned ONThe Use Cleaning Tape LED will be turned on whenever the dri

High Humidity 6-7 High HumidityTo minimize the chance of condensation, please observe the following guidelines:• If you expose cartridges to temperat

6-8 Troubleshooting and Diagnostic 62-0162-01

ASpecificationGeneral Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-3

A-2 Specification 62-0162-01

General Specification A-3 A-General SpecificationThis section contains specification information on the 4000/7000DLT Series. See Table A-1.Table A-1

Figuresvii Figure 2-1 7000DLT Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-6Figure 2-2 4000DLT Front Pa

A-4 Specification 62-0162-01Vibration: 0.25G (5-500 Hz) (Operating)0.5G (5-500 Hz) (Storage/Shipping)Shock: 2G Operating30G Storage/ShippingTable A-1

BDrive ConfigurationDrive Dependent Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .B-3SCSI Bus

B-2 Drive Configuration 62-0162-01

Drive Dependent Configuration B-3 B-Drive Dependent ConfigurationThis section describes the options you can select by installing jumpers on the DLT T

B-4 Drive Configuration 62-0162-01DLT7000 DriveIf your host computer system does not generate SCSI bus parity, you can disable parity checking in the

SCSI Bus Termination and Terminator Power B-5 SCSI Bus Termination and Terminator PowerThe following paragraphs describe information about terminatio

B-6 Drive Configuration 62-0162-01Figure B-6 TRM PWR/TRM ENB Jumper PositionIf . . . And . . . Then You Should . . .Another device is providing termi

SCSI Bus Termination and Terminator Power B-7 DLT7000 DrivesThe DLT7000 drive can be configured to supply terminator power, by jumpering specific pin

B-8 Drive Configuration 62-0162-01

CRegulatory NoticesFCC Notices (U.S. Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3Shi

viii Figures 62-0162-01

C-2 Regulatory Notices 62-0162-01

FCC Notices (U.S. Only) C-3 C-FCC Notices (U.S. Only)This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

C-4 Regulatory Notices 62-0162-01Product Type The following information is provided on the device or devices covered in this document in compl

EN 55022 Compliance (Czech Republic Only) C-5 EN 55022 Compliance (Czech Republic Only)This device belongs to category B devices as described in EN 55

C-6 Regulatory Notices 62-0162-01EN 61000-4-4 "Electromagnetic compatibility for industrial-process measurement and control equipment Part 4: El

Index- 1 -10.0 format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-710.0 GB format . . . . . . . . . . . . . . . . . . . . . . 2-4,

in-8 Index 62-0162-01disable parity . . . . . . . . . . . . . . . . . . . . . . .B-3, B-4drive error messages . . . . . . . . . . . . . . . . . . .

Index in-9 SCSI ID switch . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5SCSI Interface Cable . . . . . . . . . . . . . . . . . . . . 2-12S

in-10 Index 62-0162-01

Tablesix Table 2-1 Maximum Capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Table 2-2 Transfer Rate (Compre